|
SUBLIME®
SUBLIME® is a water-based solvent containing wetting agents, corrosion
inhibitors and degreasing compounds. It is designed to
penetrate and remove encrusted lime
scale, rust, and corrosion products and dirt from water-wetted surfaces in process
equipment,
commercial and industrial applications.
SUBLIME®
has a pleasant citrus-lime
fragrance that masks the obnoxious odors normally associated with dissolving water scale
and corrosion. It is low-foaming and quickly releases the carbon dioxide (CO2
) gas generated by the reaction of lime scale
with
SUBLIME®.
SUBLIME CHANGES
COLORS!
SUBLIME® comes in a pale yellow
color that changes to a deep bluish-purple when it is spent. The advantages to this color
change
are:
-
You know when the solution is spent and should be
discarded
-
Don’t
spend time circulating a spent solution,
-
The color change occurs at a pH of 5.8 to 6.0
which is well within the safe disposal range of most of the current governmental
waste
regulations and
-
If the equipment is clean and SUBLIME®
has not changed
color, you can save it and use it again.
SUBLIME® is most effectively used
by circulating through the equipment to be cleaned. When possible, circulation should be
up-flow. SUBLIME®
can also be used by filling the equipment to be
cleaned and allowing it to set until scale has disappeared. The cleaning
operation
normally takes two to six hours.
SUBLIME®
is non-toxic, non corrosive,
non-flammable and non-hazardous when used as directed.
SUBLIME®
is U.S.D.A. approved as
specified in 40 CRF 261. and D.O.T. 173.240(a)
SUM-KOOL®
-
Neutral compound (no acid)
-
Based on chelating agents
-
Designed for closed loop systems and systems containing
aluminum
The problems caused by water related scale, rust, and
corrosion affect every industry from nuclear power plants to automobile engines.
It has
been shown that 1/16 of an inch of scale is equivalent to approximately 3 inches of steel
in heat transferability.
SUM-KOOL® is an effective and efficient heat transfer
system cleaner designed to remove encrusted lime scale, rust, and corrosion
products from
water-wetted surfaces.
-
SUM-KOOL® is non-toxic, non-hazardous and
biodegradable
-
SUM-KOOL® is non-acid and does not require
neutralization
-
SUM-KOOL® operates in a pH range from 6.0 to 8.5 and
can be safely disposed in municipal water handling operations
SUM-KOOL® is non-corrosive and will not adversely
affect the following materials: stainless steel, carbon steel, brass, admiralty metal,
copper, iron, lead, aluminum, PVC plastic, polyethylene, rubber, leather, or any metal or
material normally found in water-wetted
equipment.
ALIMEX
A Water Scale
Solvent that is Safe for Aluminum
ALIMEX is a water-based
chemical formulated to safely clean lime scale and corrosion from water-wetted surfaces.
It contains wetting
agents, corrosion inhibitors and degreasing compounds to help
penetrate and carry away the scale and corrosion. This product is
specifically designed to
be used on equipment that contains aluminum that cannot be safely cleaned with other scale
removing
compounds.
When used as directed, ALIMEX
is non-corrosive and
will not affect the following metals: aluminum, stainless steel, carbon steel,
brass,
admiralty metal, copper, iron, lead, PVC plastic, polyethylene, rubber leather, and most
materials found in water-wetted equipment. ALIMEX
is not recommended for zinc,
galvanized steel, or alloys of magnesium.
ALIMEX
is non-toxic, non-corrosive, and
non-flammable when used as directed. It is biodegradable and can be safely put into the
sewer in the spent condition.
ALIMEX
has a built-in indicator which changes color
when the solution is 95+ percent spent. When the solution begins to turn blue,
it should be added to or changed
if the equipment is not clean.
MORCON-10
Mortar & Concrete Remover
MORCON-10 was developed to remove cement and other
calcium materials (lime-scale, barnacles, mussels) from places where they
may cause a
problem.
MORCON-10 is a hydrochloric acid solution that
contains corrosion inhibitors, detergents, wetting agents and degreasing compounds.
It is designed to
penetrate encrusted scale, cement, and barnacles and quickly remove them from the surface.
MORCON-10 is not recommended
for use on aluminum, certain alloys, zinc, and alloys of
magnesium. The improper use of Morcon-10
could result in the
discoloration of automotive paint finish.
back to Summit
|
